Digital instructions for use: what Regulation (EU) 2023/1230 requires

Updated on .

Regulation (EU) 2023/1230 on machinery applies from 20 January 2027. Article 10(7) allows the instructions for use to be provided in digital format, under specific conditions. This guide sets out the text requirement by requirement and, for each one, what FactoryDocs does.

This guide sets out the text of the Regulation and is not legal advice. The quotations are taken from the official English text published on EUR-Lex.

At a glance

When the instructions for use are provided in digital format (Article 10(7) (opens in a new tab)):

  • how to access them must be marked on the machinery or, where that is not possible, on its packaging or in an accompanying document (point (a));
  • it must be possible to print and download them and save them on an electronic device (point (b));
  • they remain accessible online during the expected lifetime of the machinery and for at least 10 years after it is placed on the market (point (c));
  • if the user requests it at the time of the purchase, the manufacturer provides the paper copy free of charge within one month (third subparagraph);
  • for machinery intended for non-professional users, or that they can use under reasonably foreseeable conditions, the safety information that is essential goes on paper (fourth subparagraph);
  • the language is the one determined by the Member State concerned (last subparagraph).

When it applies

The Regulation “shall apply from 20 January 2027” (Article 54 (opens in a new tab)). From that date Directive 2006/42/EC is repealed (Article 51(2) (opens in a new tab)). The date is the one set by the corrigendum published in Official Journal L 169 of 4 July 2023, which corrected the “14 January 2027” of the original text (opens in a new tab).

Some Articles apply earlier: Articles 26 to 42 from 20 January 2024, and Article 50(1) from 20 October 2026.

Article 10 has not changed since 2023. The two Regulations that have amended Regulation (EU) 2023/1230, (EU) 2024/2748 and (EU) 2026/1744, do not touch Article 10 or Annex III, section 1.7.4.

For machinery placed on the market before 20 January 2027, see the frequently asked questions.

Instructions may be digital

Manufacturers shall ensure that the machinery or related products are accompanied by the instructions for use and the information set out in Annex III. The instructions may be provided in a digital format. Such instructions and information shall clearly describe the product model to which they correspond.

(Article 10(7), first subparagraph (opens in a new tab))

It is an option. The second subparagraph sets the conditions, in points (a), (b) and (c).

Marking on the machinery how to access them

(a) mark on the machinery or related product, or, where that is not possible, on its packaging or in an accompanying document, how to access the digital instructions;

(Article 10(7), second subparagraph, point (a) (opens in a new tab))

The text names no technology: it mentions neither QR codes nor links. It says where the information goes: on the machinery and, only where that is not possible, on its packaging or in an accompanying document.

With FactoryDocs. Every machine sheet has its own QR code, and so does every serial number. You download it as SVG or PNG and apply it to the nameplate, the packaging or an accompanying document. The QR code opens the sheet in the browser, with no app, and you can change where it leads without reprinting it.

QR codes

Print, download, save

(b) present them in a format that makes it possible for the user to print and download the instructions for use and save them on an electronic device so that he or she can access them at all times, in particular during a breakdown of the machinery or related product; this requirement also applies where the instructions for use are embedded in the software of the machinery or related product;

(Article 10(7), second subparagraph, point (b) (opens in a new tab))

With FactoryDocs. In the machine sheet, the instructions are documents, PDFs for example. Anyone who scans the QR code opens them in the browser, downloads them and saves them on their device, or prints them. You choose the file format. The sheet is a web page and opens with a connection: without a network, you consult the downloaded copy.

The machine sheet

Online for the expected lifetime

(c) make them accessible online during the expected lifetime of the machinery or related product and for at least 10 years after the placing on the market of the machinery or related product.

(Article 10(7), second subparagraph, point (c) (opens in a new tab))

The text requires both periods: the expected lifetime and at least 10 years after the placing on the market. “Lifetime” is defined in Article 3, point (34) (opens in a new tab): “the period from the moment that machinery or a related product is placed on the market or put into service until the moment that it is discarded, […]”.

With FactoryDocs. The printed QR code holds a fixed address, on your domain: the content changes, the code does not. At the end of the contract, Inmagik exports the published content. If you put it online on the same domain, the addresses of the QR codes remain valid. The obligation stays with the manufacturer, whatever service it uses to publish the instructions.

Domain, brand and export

Contents and the product model

The instructions, digital or on paper, “shall clearly describe the product model to which they correspond” (Article 10(7), first subparagraph (opens in a new tab)).

The rules on contents add to those on format. Annex III, section 1.7.4 (opens in a new tab), opens with: “In addition to the obligations set out in Article 10(7), instructions for use shall be drawn up as set out below.” Section 1.7.4.2 lists the contents of the instructions, from point (a) to point (x).

With FactoryDocs. One sheet for each model, with the machine type and a description at the top. From the QR code of a serial number, the serial number and the data of that unit appear too. The contents of the instructions remain yours: FactoryDocs publishes them, it does not check them.

The machine sheet

The paper copy on request

However, at the request of the user at the time of the purchase, the manufacturer shall provide the instructions for use in paper format free of charge within one month.

(Article 10(7), third subparagraph (opens in a new tab))
  • Who requests it: the user.
  • When: at the time of the purchase.
  • Cost: free of charge.
  • Time limit: within one month. The text does not say when the month starts.

Recital (40) (opens in a new tab), which is not binding, adds: “the manufacturer should ensure that distributors can provide, at the request of the user at the time of the purchase, the instructions for use in a paper format free of charge. The manufacturer should also consider providing the contact details where the user can request the instructions to be dispatched by mail.”

With FactoryDocs. FactoryDocs does not handle requests for paper copies. The documents of the sheet are files you can print, and in the Service section of the sheet you can say whom to ask for the copy.

Non-professional users

In the case of machinery or a related product intended for non-professional users or that can, under reasonably foreseeable conditions, be used by non-professional users, even if not intended for them, the manufacturer shall provide, in paper format, the safety information that is essential for putting the machinery or related product into service and for using it in a safe way.

(Article 10(7), fourth subparagraph (opens in a new tab))

The obligation also covers machinery not intended for non-professional users, if they can use it under reasonably foreseeable conditions.

Annex III, section 1.7.4.1, point (b) (opens in a new tab), adds: “In the case of machinery or related products intended for use by non-professional operators, the wording and layout of the instructions for use shall take into account the level of general education and acumen that can reasonably be expected from such operators.”

With FactoryDocs. This information goes on paper: the digital sheet can accompany it, not replace it.

Language

The instructions for use, the safety information and the information set out in Annex III shall be in a language which can be easily understood by users, as determined by the Member State concerned, and shall be clear, understandable and legible.

(Article 10(7), last subparagraph (opens in a new tab))
  • Specialised maintenance. “By way of exception to Article 10(7), the maintenance instructions intended for use by specialised personnel mandated by the manufacturer or its authorised representative may be supplied in only one official language of the Union which the specialised personnel understand.” (Annex III, section 1.7.4 (opens in a new tab))
  • Information and warnings on the machinery. “Any written or verbal information and warnings must be expressed in a language which can be easily understood by users, as determined by the Member State concerned.” (Annex III, section 1.7.1 (opens in a new tab))
  • EU declaration of conformity. It “shall be translated into the language or languages required by the Member State in which the machinery or related product is placed on the market, is made available on the market or put into service” (Article 21(2) (opens in a new tab)).
  • Italy. Italian Law No 36 of 17 March 2026, in Article 9(2)(f), delegates to the Government the task of determining the language of the documentation required by these provisions.

With FactoryDocs. Each sheet has the content languages of its sheet group, with its own texts and files for each language. The same QR code opens every language, and whoever scans it sees the language of their browser.

Multilingual content

The EU declaration of conformity

The EU declaration of conformity can already be digital today.

Manufacturers shall ensure that the machinery or related product is accompanied by the EU declaration of conformity set out in Annex V, Part A or, alternatively, manufacturers shall provide the internet address or machine-readable code where that EU declaration of conformity can be accessed in the instructions for use and the information set out in Annex III.

Digital EU declarations of conformity shall be made accessible online for the expected lifetime of the machinery or related product and in any event for at least 10 years after the placing on the market or the putting into service of the machinery or related product.

(Article 10(8) (opens in a new tab))

The contents of the instructions include “the EU declaration of conformity, or the internet address or machine readable code, where the EU declaration of conformity can be accessed, in accordance with Article 10(8)” (Annex III, section 1.7.4.2, point 1(c) (opens in a new tab)).

With FactoryDocs. The declaration can sit among the documents of the machine sheet, for example in a “Certifications” folder, reachable from the same QR code. If you draw up a declaration for each serial number, you attach it to the serial number: each serial number has up to two documents of its own, which open from its QR code.

QR codes

Changes under way

The Omnibus IV package (proposal COM(2025) 504, procedure 2025/0134(COD)) would also amend Regulation (EU) 2023/1230. It is not in force.

  • The instructions do not change. The proposal does not amend Article 10(7): the rules described in this guide remain.
  • Declaration of conformity in digital format only. The manufacturer draws up the EU declaration of conformity in digital format. The machinery is accompanied by the internet address or machine-readable code through which the declaration can be directly accessed.
  • “Digital contact”. The instructions also give the digital contact of the manufacturer, alongside its name and postal address. It is an up-to-date and freely accessible online communication channel, such as an email address, through which the manufacturer can be contacted without registering and without installing apps.
  • When it would apply. Under the agreed text, to machinery 30 months after the entry into force of the regulation introducing the amendments. The date depends on publication in the Official Journal and cannot be calculated today. From 20 January 2027, therefore, the current text of Article 10(7) and (8) applies.
  • Where it stands, as of 20 November 2026. The European Parliament and the Council reached a provisional agreement on 9 June 2026. Coreper confirmed it on 26 June 2026 and the Parliament’s IMCO committee approved it on 14 July 2026. What remains is the Parliament’s plenary vote, the adoption by the Council and the publication in the Official Journal.

Frequently asked questions

Sources

  • Regulation (EU) 2023/1230 (opens in a new tab), Official Journal L 165 of 29 June 2023
  • Consolidated version of 27 July 2026 (opens in a new tab)
  • Corrigendum, Official Journal L 169 of 4 July 2023, p. 35
  • Proposal COM(2025) 504 and procedure 2025/0134(COD) on the European Parliament’s Legislative Observatory
  • Council of the European Union, document ST 10980/26 of 26 June 2026 (agreed text)
  • European Commission, Guide to application of the Machinery Directive 2006/42/EC, edition 2.3, April 2024
  • Italian Law No 36 of 17 March 2026, Article 9

Your machines’ digital instructions, on board the machine.

Try FactoryDocs on one of your machines: a sheet with the instructions, its QR code and the languages of your markets.

Request a free trial
TRANSPARENCY FIRST

Privacy and cookies.

This notice describes the features of the FactoryDocs website. The product is made by INMAGIK srl (opens in a new tab), Via Sant’Orsola 2, Bergamo, VAT No. 03934600168.

Contact requests

The form sends your name, email, company and request details to the Inmagik CRM, together with the confirmation that you have read the privacy policy. The data is used to reply to your request and is not saved by the website in the browser’s storage. The confirmation that your request has been sent only appears when the CRM accepts it. For the processing of your data by Inmagik, see its privacy policy (opens in a new tab).

Statistics and preferences

If you choose “Accept”, Google Analytics 4 collects statistics on the use of the site through cookies and sends the related data to Google. The tag and the requests to Google stay turned off until you make your choice. You can change your mind at any time from “Privacy and cookies”. Your preference is remembered for six months; if you withdraw it, no new data is collected from that moment on.

Your choice is kept in localStorage on your device and is not sent to the server. Fonts and images are served by the site.

Hosting and external links

The hosting platform may handle technical connection data needed to serve the site. External links open sites with their own privacy policies.

Contact and rights

For information about the data sent to Inmagik, or to exercise your rights, write to info@inmagik.com. See also the Inmagik terms of service (opens in a new tab). The demo is illustrative; the terms of the service and the retention of content are set out in the product contract.